Search Results

Accident statistics show that rollover accidents contribute to a large proportion of fatal traffic accidents in the U.S.. In the past it has been documented that some light passenger cars showed tendencies to roll over in evasive lane change maneuvers. In 1997, a newly developed mini van rolled over in a severe double lane change test called “moose-test”. Recently (2001), a new SUV showed similar tendencies in the Consumers Union Short Course test. It is not immediately clear why these evasive test maneuvers are so strongly related to untripped rollover of light passenger vehicles. Therefore, the goal of current research is to understand the circumstances and effects causing modern passenger vehicles to roll over in evasive maneuvers on the road. This paper discusses research activities concerning the following questions: How do critical steering strategies lead to untripped rollover? Are resonant frequencies excited during maneuvers leading to rollover?

Topology optimization in structural analysis is known for many years. In the presented procedure, “topology optimization” is used for computational fluid dynamics (CFD) for the first time. It offers the possibility of a very fast optimization process under utilization of the physical information in the flow field instead of using optimization algorithms like for example evolution strategies or gradient based methods. This enables the design engineer to generate in a first layout air guiding systems with low pressure drop in a fast and easy manner, which can than be improved further due to constraints of styling or production requirements. This procedure has been tested with many examples and shows promising results with a reduction in pressure loss up to 60% compared to a duct designed in CAD in the traditional way.

Permanently increasing software complexity of today's electronic control units (ECUs) makes testing a central and significant task within embedded software development. While new software functions are still being developed or optimized, other functions already undergo certain tests, mostly on module level but also on system and integration level. Testing must be done as early as possible within the automotive development process. Typically ECU software developers test new function modules by stimulating the code with test data and capturing the modules' output behavior to compare it with reference data. This paper presents a new and systematic way of testing embedded software for automotive electronics, called MTest. MTest combines the classical module test with model-based development. The central element of MTest is the classification-tree method, which has originally been developed by the DaimlerChrysler research department.

Today's interior systems engineer has been challenged with providing cost-effective instrument panel design solutions to meet NHTSA's new FMVSS 208 front crash regulations. Automotive manufacturers are in continuous search of newer methods and techniques to reduce prototype tests and cost. Analytical methods of predicting occupant and structural behavior using computer-aided engineering (CAE) analysis has been in place for quite some time. With the new FMVSS 208 regulations requiring both 5th and 50th percentile occupant testing, CAE analysis of predicting occupant response has become increasingly important. The CAE analyst is challenged with representing the barrier test condition, which involves the structure and the occupant moving at velocities of 25, 30 and 35 mph. Representing the cab kinematics in high-speed impacts is crucial, since capturing the vehicle intrusion and pitching should be made part of the input variables.

In view of tight emission standards, injection strategies to reduce raw HC-emissions during the cold starting of port fuel injected engines are evaluated in this study. The relevance of spray targeting and atomization is outlined in the first part of this paper. The foundation and performance of different injector concepts with respect to spray characteristics are discussed. Laboratory experiments demonstrate that concepts relying on auxiliary energy, such as air-assistance, fuel heating and injection at elevated system pressures, are capable of producing spray droplet sizes in the SMD-range of 25μm. For future injection strategies aimed at the compliance of SULEV emission levels, this target value is considered to be essential. In the second part of this paper, emission tests of selected injector concepts are carried out using a V6-3.2I ULEV engine operated both in a vehicle and on a test bench.

Suspension systems have a major effect on the handling characteristics of a vehicle, particularly ride comfort and handling safety, and thus substantially determine its character. Their increasing significance is reflected by the greater value that ever more demanding customers attribute to the properties ride comfort and handling safety. Now that the potential of conventional, passive systems is largely exhausted, adaptive and active systems open up new possibilities, e.g.: the suppression of rolling and pitching movements, handling and ride height independent of load, handling characteristics and ride height adaptable to situation and customer requirement. The DaimlerChrysler active suspension and damping system (Active Body Control – ABC) manages to resolve the conflict of aims between handling safety and ride comfort which afflicts conventional fixed suspension systems, and as a result offers greater freedom of layout whilst enabling optimization of both target criteria.

A simple strategy for building lightweight automobile body-in-whites (BIWs) is developed and discussed herein. Because cost is a critical factor, expensive advanced materials, such as carbon fiber composites and magnesium, must only be used where they will be most effective. Constitutive laws for mass savings under various loading conditions indicate that these materials afford greater opportunity for mass saving when used in bending, buckling or torsion than in tensile, shear or compression. Consequently, it is recommended that these advanced materials be used in BIW components subject to bending and torsion such as rails, sills, “A-B-C” pillars, etc. Furthermore, BIW components primarily subject to tension, compression, or shear, such as floor pans, roofs, shock towers, etc., should be made from lower cost steel. Recommendations for future research that are consistent with this strategy are included.

The current is an investigation of the effects of charge motion, namely tumble, on the burn characteristics of the new Chrysler Hemi SI engine. In order to reduce prototyping, several combustion system designs were evaluated; some of which were eliminated prior to design inception solely based on CFD simulations. The effects of piston top and number of spark plugs were studied throughout the conceptual stage with the AVL-FIRE CFD code. It has been concluded that large-scale, persistent and coherent tumbling flow structures are essential to charge motion augmentation at ignition only if such structures are decimated right before ignition. Piston top had a detrimental effect on tumbling charge motion as the piston approaches the TDC. When compared to single spark plug operation, dual spark plug reflected considerable improvement on burn characteristics and engine performance as a consequence. The CFD simulations demonstrated good correlation with early dynamometer data.

In order to fulfill the need for an efficient and reliable computational method for the aerodynamic optimization of passenger cars, a numerical simulation strategy has been developed at DaimlerChrysler in Stuttgart. The simulation strategy consists of surface preparation, three dimensional mesh generation, flow simulation using CFD, and post-processing. The method will be applied mainly in the early concept phase of the development process when 1:4 scale models with smooth underbodies are used. In this study SAE-bodies as well as modifications of real car shapes are presented. The paper also discusses which improvements are needed to establish a mainly CFD-based process in the early concept phase.

The NO distribution in a directly-injected Diesel engine with realistic combustion chamber geometry was investigated with laser-induced fluorescence (LIF) imaging with KrF excimer laser excitation. The highest possible level of selectivity has been ensured using spectrally resolved LIF investigations inside the Diesel engine. To minimize interference from both, oxygen and polycyclic aromatic hydrocarbon (PAH) LIF the NO signal was detected around 237 nm, blue-shifted compared to the excitation wavelength resulting in a background contribution below 10% at the earliest detection timing possible in the engine under study (20°ca after top dead center, TDC). The in-cylinder NO LIF intensities were compared for different injection systems and operating conditions and correlated to variations in pressure traces and soot temperature measurements.

A look at the various past achievements in the field of passenger car safety raises the question whether any dramatic steps towards its improvement can still be expected. Will progress be confined to the optimization of existing systems or does the future hold new substantial safety steps? This paper elaborates on the issue that the time available before a potential accident occurs can be used to improve the safety of occupants and other involved road users. Accident analysis confirms that this is feasible for about two-thirds of all accidents. The recognition of an imminent collision bears a noteworthy potential for accident prevention, reduction of accident severity and injury severity. The former boundary between active and passive safety thus fades continually. Based upon this it is possible to describe vehicle safety by a comprehensive approach encompassing seven escalation levels.

In the present study, the exterior air flow over convertibles together with the interior flow in the passenger compartment has been calculated using the commercial CFD program STAR-CD. The investigations have been performed for a SLK-class Mercedes with two occupants. The computational mesh consists of about 3 million hexahedra cells. The detailed informations of the calculated flow field have been used to elaborate the characteristic flow phenomena and increase the physical understanding of the flow. The influence of different geometrical modifications (variations of roof spoiler, variations of the draft stop behind the seats etc.) on the flow field and the air draft experienced by the occupants has been analyzed. To proof the accuracy of the numerical results, wind tunnel experiments in a full scale and 1:5 scale wind tunnel have been carried out for the basic car model as well as for several geometrical variations.

This paper introduces the new 1.6L engine family, designed and developed by the Chrysler group of DaimlerChrysler Corporation in cooperation with BMW. An overview of the engine's design features is provided, with a detailed review of the performance development process with emphasis on airflow, combustion, thermal management and friction. This information is presented, to provide an understanding of how the engine simultaneously achieves outstanding levels of torque, power, fuel consumption, emissions and idle stability. The use of analytical tools such as Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA) in the optimization of the engine is shown.

Today, a number of simulation codes are available for pre-designing gas exchange systems of IC engines with good accuracy (e.g. PROMO, WAVE, GT-Power). However, optimizing such systems still requires numerous time consuming and inefficient trial and error runs. Also, accounting for constraints as size, volume, peak combustion pressure etc. multiplies the necessary efforts additionally. Hence there is a strong need for efficient procedures for finding optimum designs automatically and reliably. To automatically find the global optimum design parameters under a given set of real constraints of a practical case, a multi-membered evolution-strategy based optimization code was developed. The code which efficiently finds the true optimum dimensions of gas exchange systems (duct lengths, duct diameters, volumes) of an IC engine. The code can be readily generalized, and adapted to arbitrary optimization problems.

Coming along with the present movement towards the ultimately variable engine, the need for clear and simple models for complex engine systems is rapidly increasing. In this context Common-Rail-Systems cause a special kind of problem due to of the high amount of parameters which cannot be taken into consideration with simple map-based models. For this reason models with a higher amount of complexity are necessary to realize a representative behavior of the simulation. The high computational time of the simulation, which is caused by the increased complexity, makes it nearly impossible to implement this type of model in software in closed loop applications or simulations for control purposes. In this paper a method for decreasing the complexity and accelerating the computing time of automotive engine models is being evaluated which uses an optimized method for each stage of the diesel engine process.

We are the first to report about a micromachined flow sensor directly integrated in the Common Rail injection nozzle body between the double guidance and the tip of the nozzle. The thermal measurement principle is chosen, because it enables a very precise and fast detection of gaseous and liquid mass flows. Additionally, the velocity field in the nozzle is only slightly influenced by the integration of the sensor in the nozzle body due to the negligible height of the sensitive layer. For a hot film anemometer, a high pressure stable ceramic substrate can be used, fabricated in a low cost batch process. The technology, to fabricate the sensor, as well as the first flow measurements, carried out at a high pressure test set up, are presented.

BMW, DaimlerChrysler, Motorola and Philips present their joint development activity related to the FlexRay communication system that is intended for distributed applications in vehicles. The designated applications for powertrain and chassis control place requirements in terms of availability, reliability and data bandwidth that cannot be met by any product currently available on the market under the testing conditions encountered in an automobile. A short look back on events so far is followed by a description of the protocol and its first implementation as an integrated circuit, as well as its incorporation into a complete tool environment.

High demands in fuel consumption, efficiency, and low emissions lead to complex control functions for current and future diesel engine management systems. Great effort is necessary for their optimal calibration. At the same time, and particularly for cost reasons, many variants exist on one individual type of diesel engine management system. Not only is it used for several base engines, but these engines are also used in different environments and for different tasks. For optimal deployment, their calibration status must also be optimized individually. Furthermore, the demand for shorter development cycles and enhanced quality lead to a catalogue of new requirements for the calibration process and the affiliated tool. A new calibration system was developed, which optimally reflects the new demands.

The increase of active safety will demand more and more electronic intelligence, if a drastic optimization of conventional systems is not possible any more. Starting from today's mechatronic systems, the trend leads via tomorrow's smart electronic systems to the future electronic networking of all intelligent vehicle systems. The paper describes the present status of these systems in Europe and the possibilities of increasing the active safety by using electronic intelligence.

The development of electronic intelligence and the continually increasing intensive knowledge of driving dynamics make it possible nowadays to conceive intelligent vehicle systems and to make such systems available for series production, which are capable of substantially enhancing the active safety of commercial vehicles. Through the implementation of advanced subsystems, which can be integrated as software packages into the basic electronic braking system, it will be possible to expand the possibilities of introducing assistance systems, which are capable of both, helping and relieving the driver from stress in critical situations. The driver will be relieved of all duties which could divert his attention or cause severe stress. As a consequence, the active safety of commercial vehicles will be considerably increased.